HOW TO SAVE MAJOR ECOS.??
Hi, There are many times we do not know the little things and must have the Passion and Desire to know them. Today I'm going to tell you a little bit about Information.
Hope you like it and find it useful
Most of them are in big factories, power plants, power stations The work process runs on electricity, fuel, water, heat, different chemicals Are. Proper care is taken in such places and uses as much energy as required Doing so can save a lot of energy.
1) Factories should be set up with maximum natural light and air
It will be available.
2) Maximum for ventilation on factory roof Use an automatic ventilator exhaust fan.
3) To the factory, walls Should be given a lighter color. Mayuri was needed when planning to light
Lamps, industrial fluorescent tubes, or twin-tube lights should be used. And right Install light converters.
4) Power supply lines, equipment, etc. Right
Must be of suitable size. Wires and cables of reputable companies and suitable sizes should be used for wiring. Wiring should be done keeping in mind the reduction in power transmission.
5) For a reputable manufacturer and a car of the same capacity as required
To be used.
6) If a machine has more than one motor, one of them Ensures that no motor exhaust is running outside of work. E.g. Kulant Motor.
7) Welding work should be stopped for a few minutes If so, turn off the transformer.
8) The right machine according to the needs of the work Use tools and equipment.
9) Keeping a record of each device and servicing it Do it on time and regularly.
10) Keep as little distance between the belt or chain as possible to speed up the machine. Free play should be checked regularly and set if necessary.
11) If any defect is found in a device, it should be removed immediately Should do.
12) In the air-conditioned process, the process is done as per the instructions of the manufacturer or
No, or pay attention to whether there were any leaks in the process. As well as this method
Regular maintenance should take care of the oil in the filter and compressor etc.
13) In addition to the industrial area, power generation centers, power stations at their place
A large amount of heat is generated during the work process. As well as in some processes
Steam is required for proper temperature. This vapor is generated with the help of thermal energy and transported from one place to another. Care should be taken to ensure that energy is not wasted in this energy flow. The length of vapor conductors should be kept to a minimum and their connection should be firm. Also, cover it with a heat resistant cover. Install vapor control valves where necessary.
14) Excess heat generated by generator, boiler, furnace
Being is often wasted. By regulating and using this heat, the temperature required for the processes required at the primary level should be obtained.
I hope you find the above information helpful. This is how the Information will get you on my blog. I'm sure you'll like it. Feel free to leave your feedback.
THANKING YOU.....
Hi, There are many times we do not know the little things and must have the Passion and Desire to know them. Today I'm going to tell you a little bit about Information.
Hope you like it and find it useful
 |
| ENERGY CONSERVATION |
1) Factories should be set up with maximum natural light and air
It will be available.
2) Maximum for ventilation on factory roof Use an automatic ventilator exhaust fan.
3) To the factory, walls Should be given a lighter color. Mayuri was needed when planning to light
Lamps, industrial fluorescent tubes, or twin-tube lights should be used. And right Install light converters.
4) Power supply lines, equipment, etc. Right
Must be of suitable size. Wires and cables of reputable companies and suitable sizes should be used for wiring. Wiring should be done keeping in mind the reduction in power transmission.
5) For a reputable manufacturer and a car of the same capacity as required
To be used.
6) If a machine has more than one motor, one of them Ensures that no motor exhaust is running outside of work. E.g. Kulant Motor.
7) Welding work should be stopped for a few minutes If so, turn off the transformer.
8) The right machine according to the needs of the work Use tools and equipment.
9) Keeping a record of each device and servicing it Do it on time and regularly.
10) Keep as little distance between the belt or chain as possible to speed up the machine. Free play should be checked regularly and set if necessary.
11) If any defect is found in a device, it should be removed immediately Should do.
12) In the air-conditioned process, the process is done as per the instructions of the manufacturer or
No, or pay attention to whether there were any leaks in the process. As well as this method
Regular maintenance should take care of the oil in the filter and compressor etc.
13) In addition to the industrial area, power generation centers, power stations at their place
A large amount of heat is generated during the work process. As well as in some processes
Steam is required for proper temperature. This vapor is generated with the help of thermal energy and transported from one place to another. Care should be taken to ensure that energy is not wasted in this energy flow. The length of vapor conductors should be kept to a minimum and their connection should be firm. Also, cover it with a heat resistant cover. Install vapor control valves where necessary.
14) Excess heat generated by generator, boiler, furnace
Being is often wasted. By regulating and using this heat, the temperature required for the processes required at the primary level should be obtained.
I hope you find the above information helpful. This is how the Information will get you on my blog. I'm sure you'll like it. Feel free to leave your feedback.
THANKING YOU.....
Post a Comment